Anti-glare floodlight
In order to meet the anti-glare lighting needs of railway tunnels, highway bridges, public venues and various production enterprises, the latest developed and produced anti-glare street lights are widely used in tunnels, road bridges, large-scale Floodlighting of roads and passages in facilities, factories, stations and other places.
Using protective angle design and mirror coating technology to achieve anti-glare effect, which can effectively reduce irritation to the eyes of workers and construction workers. Avoid discomfort and fatigue. Selected gas discharge light source. High light efficiency, long life, power factor greater than light transmittance, long life of up to hours.
Special surface coating and sealing treatment ensure that the lamps will never corrode or rust in harsh environments such as humidity and high temperature. The multiple anti-vibration structure design and high-strength alloy shell ensure its long-term safe operation in high-frequency vibrations such as roadbeds, rails, bridges and tunnels. There are various installation methods such as seat type, ceiling type and wall-mounted type. The illumination angle can be adjusted within a wide range up and down according to the needs of the environment.
Rated voltage/
Power factor greater than
Protection level
Anti-corrosion level
Insulation level
Pitch-to-height ratio
Inlet thread/,~
Dimensions
Weight
Equipped with light source
Order number Equipped with light source, rated power, luminous flux, average service life
, determined according to the site environment and lighting needs After fixing the installation position and method of the lamp, prepare cables of corresponding length according to the distance between the lamp and the power contact.
Unscrew the two butterfly bolts fixing the front cover on the upper part of the lamp, open the front cover, and introduce one end of the prepared cable into the lamp cavity through the compression nut of the introduction device. According to the polarity marked on the terminal block, Connect the wiring and tighten the compression nut of the introduction device.
, close the front cover, tighten the two butterfly bolts on it, and then connect the other end of the cable to the power supply to illuminate.
When multiple lamps are used in parallel, introduce the cable from another lead-in device and wire it according to the above method. When connecting a single lamp to other lamps, plug the idle lead-in device with a plug.
Loosen the fixing screws on both sides of the bracket to adjust the lighting angle of the lamp in the upper and lower range.
There is a support rod inside the lamp cavity, which can be supported as needed after opening the lamp cover.
When transporting, put the lamps in the provided cartons and add foam for shock absorption.
When in use, there will be a certain temperature rise on the surface of the lamp. This is a normal phenomenon and the center temperature of the transparent parts is relatively high and should not be touched.
When replacing a light bulb, try to use the same type of light bulb. If the type or power of the light bulb is changed, the supporting ballast should be replaced accordingly.
The temperature resistance of the cables introduced into the lamp cavity should not be lower than ℃ (such as silicone rubber, polytetrafluoroethylene cables, etc.).
Warning, do not install directly on combustible materials
Replace any cracked protective screen
When installing and maintaining lamps, the power must be disconnected first
The lamp must be reliable Ground.
The company has passed the international quality system audit and certification. This product is produced in strict compliance with international quality management system standards to ensure that product quality fully meets national standards and design requirements. The product is subject to an annual warranty (light source is guaranteed for one year) from the date of purchase. Within one year, if any malfunction occurs during normal use of the product, our company will be responsible for free maintenance.
Explosion-proof floodlight series Explosion-proof floodlight Explosion-proof platform light Explosion-proof induction lamp Explosion-proof floodlight Pocket explosion-proof flashlight Intelligent dimming Explosion-proof searchlight Dimming focus Explosion-proof headlight Intelligent dimming Explosion-proof inspection light Emergency floodlight Emergency Floodlight emergency access light anti-glare access light anti-glare access light stepless platform light anti-glare flood light anti-glare ceiling light high-efficiency flood light high-efficiency flood light anti-seismic flood light anti-seismic flood light high ceiling light high ceiling light series anti-glare Light anti-glare pathway light
NFP090 anti-glare floodlight